led数码管、数码管显示屏/彩屏专业生产厂家,承接各种数码管显示屏的定制业务,QQ:498607372 关于我们 | 联系我们 | 在线留言
国内业务热线
15626546861

led数码管

您只需一个电话我们将提供最合适的产品,让您花最少的钱,达到最好的效果

全国统一服务热线
15626546861

相关资讯

咨询热线:

15626546861

邮箱:312344894@qq.com

地址:深圳市宝安区福永街道腾丰三路3号A栋3楼

当前位置:主页 > led数码管 > 三位数码管 >

0.23英寸红光共阳圆屏led数码管XE23BS(附引脚图)

  • 咨询热线:15626546861
圆屏led数码管XE23BS说明书型号(PART NO.): XE23BS

0.23英寸红光共阳圆屏led数码管



1.说明(Description):

发光颜色(Emitted Color):红光、共阳
外观颜色(Lens Color):黑、白两色
外形尺寸(Max Size):如结构尺寸图所示

极限参数(Absolute Maximum Ratings     建议使用驱动检测


参数(Parameter) 单位(Symbol) 极限值
(Maximum Rating)
单位(Unit)
功耗  (Power Dissipation) Pd 42 mW
脉冲电流(Peak Forward Current) Ifp 100 mA
直流电流(Continuous Forward Current) Forward )Current Ifm 20 mA
反向电压(Reverse Voltage) VR 5 V
工作温度(Operating Temperature Range) Topr -40  +85
储藏温度(Storage Temperature Range) Tstg  -40  +100
静电电压(Static Voltage) Var   V

*焊接温度(Lead Sodering Temperature):260℃  for 3 seconds
*当工作温度高于25℃时,Ifm,Ifp和Id必须降低;电流降低率是-0.36mA/℃(直流驱动),或-0.86mA/℃
(脉冲驱动)功耗降低率是-0.75mW/℃。产品的工作电流不能大于对应工作温度条件Ifm或Ifp的60%。
For  operation above 25℃,  The Ifm Ifp & Pd must be derated, the Curent derating is –0.36mA/℃ for  DC
drive and  -0.86mA/℃ for Pulse drive, the power dissipation is  -0.75mW/℃. The product working current
must not more than the 60% of the Ifm or Ifp according to the working temperature.

2.
圆屏led数码管XE23BS光电特性(Optical-Electrical Characteristic     建议使用驱动检测

参数(Parameter) 测试条件
(Test CONDITING)
单位(Symbol) Min Type Max 单位(Unit)
发光强度 (Luminous Intensity) IF=10mA Iv 70   90 Mcd
正向电压 (Forward Voltage) IF=10mA VF 1.8 - 2.3 V
反向电流 (REVERSE Current) VR = 5V IR - 10   uA
波长     (Peak Wavelength) IF=10mA λp 620 - 625 nm
带宽     (Spectral Bandwidth) IF=10mA △λ - 40 - nm
查看角度 (View Angle) IF=10mA 1/2 - 60 - Deg.

3.圆屏led数码管XE23BS结构尺寸(Mechanical Outline: 
(未注尺寸公差 Unspecified Tolerances is: ±0.2    发光颜色:红色

圆屏led数码管XE23BS规格图

4.
圆屏led数码管XE23BS电路图:
圆屏led数码管XE23BS电路图

5.
圆屏led数码管XE23BS《QA成品检验方法》:
 

判定类别
Standard
判定范围
ITEM
MAJOR MINOR
 








 




Surface check condition
A. 膜纸:不齐、贴歪≥0.25mm。
Membrane:
 not uniform or deflective that must be less than 0.25mm,
B. 引脚氧化或掉铜皮、或不按要求上锡披峰。
The pins are oxygenation or lose copper or cannot meet the SPEC of soldering reliability.
C. 条形歪斜、松脱、脚短/长、膜纸变形、翘起。
Bar deflective, loss, pins short/longer,
 membrane distortion, tilt.
D. 产品弯曲、变形、划伤、毛刺。
Product inflect, scar, burr,
 
A. 膜纸不齐导致露出或超宽0.25mm内进0.25mm以下,0.15mm以上;脏、皱等。
Make for bare or exceed width between 0.25mm and 0.15mm caused by membrane were not uniform; dirty, ruck etc.
B. 产品反面非有效发光区域有手印、水渍印。
Has the fingerprint or watermark on the background of the product there are not the area of luminous.
尺 寸
检 验
Size check condition
A. 长、宽、厚等重要尺寸超差≥0.2mm,其它尺寸超差在0.25mm以上。
The tolerance of Length, width and thick must ≥0.2mm and other tolerance more than 0.25mm.
B. 膜纸过大在0.25mm以上。
Membrane over than 0.25mm
A. 虚边、毛刺等引起的尺寸超差在0.2mm以下,0.1mm以上。
The size tolerance of product that caused by burr edge shall between 0.1-0.2mm.
 
B. 小于严重缺陷的尺寸超差。
Less than the important tolerance .
功 能
发 光
效 果
检 查
Functional check condition
A. 管芯发光颜色不符合图纸要求。
The color of luminous is differenced for the SPEC.
B. 闪亮、颜色/色差、暗光、暗带与样板相差较大。
Flash, color, dark light that more difference than the golden sample.
C. 膜纸漏光直径≥0.25。
For the membrane the diameter of light Leakage≥0.25.
A. 轻微色差、暗光、暗带、暗斑。
Minor of the chromatism, dark light, dark spot.
B. 两端部发光不均匀。.
The luminescence is asymmetry at the two ends.
 

共阳led数码管数码管引脚图

订购:0.23英寸红光共阳圆屏led数码管XE23BS(附引脚图)

FPC柔性线路板 宣传片制作公司 三维动画制作 中山LED数码管